Your list is empty, add products to the list to send a request
Previous product
Back to products
Edward SIGA-CT1 Addressable Monitor Module
₹ 3,717.00 GST included
Next product
Edward EC-100R Beam Detector With Reflector (HSN 85319000)
₹ 87,910.00 GST included
Edward SIGA-COD+SIGA-SB Addressable Carbon Monoxide Detector With Mounting Base
₹ 9,888.40 GST included
Edward SIGA-COD + SIGA-SB Addressable Carbon Monoxide Detector With Mounting Base detector brings advanced sensing technology to a practical design that increases efficiency, saves installation time, cuts costs, and extends life safety capabilities. Continuous self-diagnostics ensures reliability over the long-haul, while advanced electrochemical CO sensing technology provides performance benefits that keep occupants safe from carbon monoxide, the silent killer.
In stock
Description
Edward SIGA-COD + SIGA-SB Addressable Carbon Monoxide Detector With Mounting Base detector brings advanced sensing technology to a practical design that increases efficiency, saves installation time, cuts costs, and extends life safety capabilities. Continuous self-diagnostics ensures reliability over the long-haul, while advanced electrochemical CO sensing technology provides performance benefits that keep occupants safe from carbon monoxide, the silent killer. Like all Signature Series detectors, the SIGA-COD is an intelligent device that gathers analog information from its CO sensor, converting this data into digital signals. To make an alarm decision, the detectors on-board microprocessor measures and analyzes sensor readings over time. Digital filters remove signal patterns that are not typical of life safety events, thus virtually eliminating unwanted alarms. The SIGA-COD includes an advanced carbon monoxide sensor. When the electrochemical cell reaches its end of life after approximately ten years, the detector signals a trouble condition to the control panel. Refer to the control panel documentation for specific end of life timing.
Features
- Next Generation CO Sensing Technology
- Advanced electrochemical carbon monoxide sensing technology
- Uses existing wiring
- Automatic device mapping
- Sensor Markings Provide Easy Testing Identification
- Up To 250 Total Signature Adresses Per Loop
- Non-volatile memory
- Electronic addressing
- Automatic day/night sensitivity adjustment
Specifications
- Brand: Edward
- Condition New
- Usage/Application Fire Detection
- Operating Voltage 15.20 to 19.95 VDC
- Normal operating current 32 ohmA
- Vibration level 10 to 35 Hz, with an amplitude of 0.01 in.
- Compatible detector testers Testifire 1000, Testifire 2000
- Operating environment 32 to 120 DegreeF (0 to 49 DegreeC), 0 to 90% RH, noncondensing
- Construction High Impact Engineering Polymer, White
- Storage temperature -4 to 140DegreeF
- Storage temperature -4 to 140DegreeF
Related products
Close
Solo 423-001 Heat Detector Tester 110/120 Volt
SOLO 423-001 No Climb Heat Detector Tester Mains powered heat detector tester. Available in both 110 / 120 and 220 / 240 volt versions the Solo 423 and 424 are the professionals choice where cables and leads are acceptable.
Close
C-9105R Conventional Reflective Beam Detector
C-9105R Conventional Reflective Beam Detector is an addressable reflective infrared beam smoke detector that can be directly connected to a fire alarm controller, by transmitting status information via a bus between the detector and controller. The detector must be used together with a reflector. The number of reflectors (s) to be used (one or four) depends on the distance from the detector. With a built-in intelligent microprocessor, the detector has a strong ability for analysis and judgment.
Close
Agni Hunt AHHD-16 Heat Detector
Agni Hunt AHHD-16 Heat Detector fire alarm Heat Detectors Provide high quality, reliability, and the ultimate in design and decor. The low silhouette and pure white finish blend with most ceiling styles to provide an inconspicuous unit.
Close
Mcp-yellow Ravel Make
Mcp-yellow Ravel MakeManual call point is a trigger mechanism which helps in identifying the building or an area where fire has occurred in order to Detect the attention of personals to that area. Fire Alarm manually in case of any emergency or if fire/smoke is visible
Close
TX7130R Conventional Reflective Beam Detector
TX7130R Conventional Reflective Beam Detector has built in Laser beam pointing and Digital guide display for a real user-friendly alignment method. The Laser beam pointing accurately point the exact location where to mount mirror and with additional digital guide display allows to monitor and guide on the actual light intensity between the mirror and detector which cannot be seen by our naked eye making it more easy and convenient in alignment commissioning.
Close
Agni Hunt AHHD-650 Heat Detector
Agni Hunt AHHD-650 Heat Detector fire alarm Heat Detectors Provide high quality, reliability, and the ultimate in design and decor. The low silhouette and pure white finish blend with most ceiling styles to provide an inconspicuous unit.
Close
RE317DHL Heat Detector-ravel Make
Heat Detector-ravel Make Heat Detectors Provide high quality, reliability, and the ultimate in design and decor. The low silhouette and pure white finish blend with most ceiling styles to provide an inconspicuous unit.
Close
Agni Hunt AHHD-12 Heat Detector
Agni Hunt AHHD-12 Heat Detector fire alarm Heat Detectors Provide high quality, reliability, and the ultimate in design and decor. The low silhouette and pure white finish blend with most ceiling styles to provide an inconspicuous unit.
Reviews
Questions & Answers
Questions and answers of the customers
There are no questions yet. Be the first to ask a question about this product.
Reviews
There are no reviews yet.